Is a vertical bar a cantilever

Installation aid for cable tray system RKSM

Application center suspension

Direct central suspension with threaded rod type 2078 / M10. This installation variant is possible with RKS cable trays with a width of 50 to 200 mm.

Application ceiling mounting U support with bracket

Standard installation of a cable tray with hanging support type US and matching support bracket type AW.

Application wall mounting with bracket

Standard installation of cable tray on the wall with wall and support brackets.

Quick fastening of the cable tray on the bracket

The quick-release fastener is pushed up and rotated by 90 °. After it has clicked into place, the quick-release fastener is permanently attached by tightening.

Straight connection cable tray, sleeve assembly

The straight connection is made by simply nesting the cable trays. Please note the mounting direction!

Straight connection cable tray, sleeve assembly

The cable tray that continues to run is inserted into the existing sleeve opening from above.

Straight connection cable tray, sleeve assembly

The optimal longitudinal connection is confirmed by a click sound. Then use a screwdriver to flip the connecting straps in the floor - that's it.

Straight connection cable tray, sleeve assembly

The connection tabs in the bottom of the cable tray can be turned over with a standard screwdriver.

Loosen the connection

Of course, the connection can be released again. To do this, simply slide a screwdriver under the spring element. The function of the lock is canceled.

Straight connector set Magic KTSMV

Cable tray connector set with quick fastening for screwless connection of cable trays and fittings. Thanks to the optimized design, the connector can be used to create radii and as a length compensation piece in the event of large temperature fluctuations.

Assembly of the Magic KTSMV straight connector set

The Magic KTSMV straight connector set is used for cut ends. Simply clamp the two side parts in the side rail and press the associated joint strip down until it clicks into place - done.

Assembly of the Magic KTSMV straight connector set

To reinforce the connection, screwing the joint strip is recommended from a width of 400 mm.

Floor fastening

Floor fastening at a distance with spacer bracket type DBL.

Horizontal angle connection of cable trays

Horizontal angle connection of cable trays with angles created on site and cut cable tray ends.

Horizontal angle connection of cable trays

Horizontal angle connection of cable trays with angles created on site and cut cable tray ends.

Vertical articulation of cable trays

Vertical articulated connection of cable trays with height changes created on site with any angles.

Change in width and end closure

Representation of a change in width by installing the reduction bracket. This component can also be used to terminate cable trays.

Assembly arch Magic

Assembly of molded parts by simply plugging them into one another. The spring side of the cable tray is snapped into the molded part connection from above.

Assembly of Magic add-on branch piece

Assembly of molded parts by simply plugging them into one another. The spring side of the cable tray is snapped into the molded part connection from above.

Mounting the Magic vertical branch-off piece (bottom view)

Vertical installation of the add-on branch piece as a longitudinal outlet funnel. Perforation in the cable tray is created on site. For widths> 400 mm, order connector material separately!

Mounting the Magic vertical branch-off piece (top view)

Vertical installation of the add-on branch piece as a longitudinal outlet funnel. Perforation in the cable tray is created on site. For widths> 400 mm, order connector material separately!

Assembly of the Magic T-branch

Assembly of molded parts by simply plugging them into one another. The spring side of the cable tray is snapped into the molded part connection from above.

Assembly crossing Magic

Assembly of molded parts by simply plugging them into one another. The spring side of the cable tray is snapped into the molded part connection from above.

Bend 90 ° (rising / falling)

The 90 ° vertical bend is pushed over the rail of the cable tray and screwed with truss-head screws FRSB M6x12 mm. The cover is placed loosely and fastened by means of the incoming cable tray cover.
The DKU cover clamp can be used for additional fastening.

Assembly of the articulated bend, vertically rising

Vertically rising articulated arch to bridge height offsets or to change from horizontal to vertical. The articulated bend is attached directly to the cable tray with articulated connectors.

Assembly of articulated bend falling vertically

Installation of the articulated bend falling vertically to bridge height offsets and the change from the horizontal to the vertical plane.

Assembly of the bottom end plate

The bottom end plate is attached to the end of the cable tray. It is used to protect outgoing cables and lines.

Mounting plate with quick fastening

Attachment of the mounting plate type MP to the side rail of the cable tray. The mounting plate can be fixed to the stile with the quick-release fastener and permanently fixed with truss-head screws type FRSB 6x12 mm.

Universal mounting plate

The MP UNI mounting plate is attached to the side rail of the cable tray using a screw connection.

Assembly of the cover with a twist lock